You can flash MTK Stock ROMs with the SP Flash Tool for MediaTek powered Android Smartphones. The SP Flash Tool enables you to flash your Android ROM both Stock and Custom. It supports installing custom recovery, unbrick any Bricked Smartphones, flash stock and firmware updates for your Mediatek devices. In this article, we show you how to flash Custom ROMs using SP Flash Tool with PC.
Materials Needed
1. Latest SP Flash tool – Click Here to Download
2. Android ADB drivers – Click Here to Download
3. Exact Stock or Custom Rom for your Smartphone. Make sure it is the exact Rom for your device
4. Laptop or PC – Click Here to Download
5. USB Data Cable
Disclaimer:
Always backup your stock or original ROM before you start any operation.
Be sure you know what you are doing before you begin.
Don't flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones you will have a brick even if you download these blocks read from a phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM. ITYUNIT will not be held responsible for any damage but may help you out of any mess!
1. Disconnect your phone if connected with USB to the PC, and turn OFF the phone completely, also take out the battery if possible (ignore this step 1, for phones with built in battery).
2. Now connect or reconnect the USB cable to the phone with the PC while the phone is still off, Windows should pop up and begin to install the MTK65XX Preloader Drivers, this only happens if you installed the Mediatek Preloader USB Drivers correctly in Windows. After they successfully installed, disconnect the USB cable again.
3. Extract SP Flash tool on your computer and launch it.
4. Open the folder you extract it to and locate flash_tool, double click on it to open.
5. Once it is launched, hit the Scatter-loading button
6. Locate the scatter file in the backup or Rom of the phone that you downloaded. It's usually a text file. (ALWAYS only load a ROM that is 100% made for your phone, flashing a wrong ROM may brick or make your phone non-bootable).
7. Hit the "Download' button in SP Flash Tool to begin the flashing process.
8. Connect your Smartphone to the computer with a USB without battery, if possible to remove. Press, Vol Down or Up so that the computer can easily detect the phone.
9. Once the Flashing is complete you will see a green circle confirming. With Download OK.
10. Close the SP Flash Tool and disconnect your phone from the computer. That's it. Flashing Completed and your Smartphone is now running the new Stock Rom you downloaded.
In case of any failure including phone bootloops, just remove battery or hard reset, then boot into recovery mode and “Factory Reset” the phone.
Materials Needed
1. Latest SP Flash tool – Click Here to Download
2. Android ADB drivers – Click Here to Download
3. Exact Stock or Custom Rom for your Smartphone. Make sure it is the exact Rom for your device
4. Laptop or PC – Click Here to Download
5. USB Data Cable
To Flash a Backup or ROM with SP Flash Tool
Disclaimer:
Always backup your stock or original ROM before you start any operation.
Be sure you know what you are doing before you begin.
Don't flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones you will have a brick even if you download these blocks read from a phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM. ITYUNIT will not be held responsible for any damage but may help you out of any mess!
1. Disconnect your phone if connected with USB to the PC, and turn OFF the phone completely, also take out the battery if possible (ignore this step 1, for phones with built in battery).
2. Now connect or reconnect the USB cable to the phone with the PC while the phone is still off, Windows should pop up and begin to install the MTK65XX Preloader Drivers, this only happens if you installed the Mediatek Preloader USB Drivers correctly in Windows. After they successfully installed, disconnect the USB cable again.
3. Extract SP Flash tool on your computer and launch it.
4. Open the folder you extract it to and locate flash_tool, double click on it to open.
5. Once it is launched, hit the Scatter-loading button
6. Locate the scatter file in the backup or Rom of the phone that you downloaded. It's usually a text file. (ALWAYS only load a ROM that is 100% made for your phone, flashing a wrong ROM may brick or make your phone non-bootable).
7. Hit the "Download' button in SP Flash Tool to begin the flashing process.
8. Connect your Smartphone to the computer with a USB without battery, if possible to remove. Press, Vol Down or Up so that the computer can easily detect the phone.
9. Once the Flashing is complete you will see a green circle confirming. With Download OK.
10. Close the SP Flash Tool and disconnect your phone from the computer. That's it. Flashing Completed and your Smartphone is now running the new Stock Rom you downloaded.
In case of any failure including phone bootloops, just remove battery or hard reset, then boot into recovery mode and “Factory Reset” the phone.
